BS EN 60794-2-30:2008 Optical fibre cables. Indoor cables. Family British Standards Institution specification for ribbon cables BS EN 60794-2-21:2012 Optical fibre cables. Indoor optical fibre cables. Detailed specification for multi- https://www.standards.govt.nz (BSI) Available through Standards New Zealand British Standards Institution https://www.standards.govt.nz (BSI) Available through Standards New Zealand fibre optical distribution cables for use in premises cabling Rationale & Controls 10.6.22. Terminations to patch panels 10.6.22.R.01. Rationale Cross-connecting a system to another system of a lesser classification through a patch panel may result in a data spill. A data spill could result in the following issues: inadvertent or deliberate access to information and systems by non-cleared personnel; and/or information spilling to a system of another classification. 10.6.22.R.02. Rationale Cross-connecting Cables run to patch panels are best managed by bundling similar classifications or groups together.RED/BLACK separations should be maintained at all times. A simple approach to this is to bundle and run RED cables up vertical rails of the cabinet andBLACK cables up the opposite side. Where multiple cabinets are installed sides may be alternated to ensure RED/RED and BLACK/BLACK groupings are maintained by running cables groups up/down/across separate rails in the cabinet or in separate conduits. 10.6.22.C.01. ControlSystem Classification(s): All Classifications; Compliance: MUST [CID:2425] Agencies MUST ensure that only approved cable groups terminate on a patch panel. 10.6.22.C.02. ControlSystem Classification(s): All Classifications; Compliance: MUST [CID:5607] RED and BLACK cables must be separated and bundled. 10.6.23. Patch cable and fly lead connectors 10.6.23.R.01. Rationale Cables equipped with connectors specific to a classification will prevent inadvertent cross-connection. These connectors can be keyed or have specific profiles to prevent connection to other systems. 10.6.23.C.01. ControlSystem Classification(s): Confidential, Secret, Top Secret; Compliance: MUST [CID:2428] In areas containing cabling for multiple classifications, agencies MUST ensure that the connectors for each classification are distinct and different to those of the other classifications. 10.6.23.C.02. ControlSystem Classification(s): Confidential, Secret, Top Secret; Compliance: MUST [CID:2429] In areas containing cabling for multiple classifications, agencies MUST document the selection of connector types for each classification. 10.6.23.C.03. ControlSystem Classification(s): All Classifications; Compliance: SHOULD [CID:2430] In areas containing cabling for systems of different classifications, agencies SHOULD ensure that the connectors for each system are different to those of the other systems. 10.6.23.C.04. ControlSystem Classification(s): All Classifications; Compliance: SHOULD [CID:2431] In areas containing cabling for systems of different classifications, agencies SHOULD document the selection of connector types. 10.6.24. Physical separation of patch panels 10.6.24.R.01. Rationale Appropriate physical separation between systems classified CONFIDENTIAL or above and a system of a lesser classification (RESTRICTED and below) will: reduce or eliminate the chances of cross patching between the systems; and reduce or eliminate the possibility of unauthorised personnel or personnel gaining access to classified system elements. Refer also to 10.1 – Cable Management Fundamentals for the discussion on RED/BLACK concept and cable separation. 10.6.24.C.01. ControlSystem Classification(s): Confidential, Secret, Top Secret; Compliance: SHOULD [CID:2434] Agencies SHOULD physically separate patch panels of different classifications by installing them in separate cabinets. 10.6.24.C.02. ControlSystem Classification(s): Confidential, Secret, Top Secret; Compliance: MUST [CID:2435] Where spatial constraints demand patch panels of different classification are located in the same cabinet, agencies MUST: provide a physical barrier within the cabinet to separate patch panels; ensure that only personnel cleared to the highest classification of the circuits in the panel have access to the cabinet; and obtain approval from the relevant Accreditation Authority prior to installation. 10.6.25. Cabinet Arrangement 110 Version_3.5__January-2022

Select target paragraph3

Connect to a paragraph
Connect to an entity
Disable highlights
Add to table of contents